Technical Parameters
Technical parameter | Parameter value |
Brand | SONBEST |
Temperature measuring range | -50℃~120℃ |
Temperature measuring accuracy | ±0.5℃ @25℃ |
Communication Interface | RS232 |
Default baud rate | 9600 8 n 1 |
Power | DC9~24V 1A |
Running temperature | -40~80°C |
Working humidity | 5%RH~90%RH |
Wiring instructions
Any incorrect wiring can cause irreversible damage to the product. Please carefully wire the cable as follows in the case of power failure, and then connect the cable to confirm the correctness and then use it again.
ID | Core color | Identification | Note |
1 | Red | V+ | Power V+ |
2 | Green | V- | Power V- |
3 | Yellow | TX | RS232 TX |
4 | Blue | RX | RS232 RX |
Communication Protocol
The product uses RS485 MODBUS-RTU standard protocol format, all operation or reply commands are hexadecimal data. The default device address is 1 when the device is shipped, the default baud rate is 9600, 8, n, 1
1. Read Data (Function id 0x03)
Inquiry frame (hexadecimal), sending example: Query 1# device 1 data, the host computer sends the command:01 03 00 00 00 01 84 0A .
Device ID | Function id | Start Address | Data Length | CRC16 |
01 | 03 | 00 00 | 00 01 | 84 0A |
Device ID | Function id | Data Length | 测点1 | 测点2 |
测点3 | 测点4 | 测点5 | 测点6 | 测点7 |
测点8 | 测点9 | 测点10 | 测点11 | 测点12 |
测点13 | 测点14 | 测点15 | 测点16 | 测点17 |
测点18 | 测点19 | 测点20 | 测点21 | 测点22 |
测点23 | 测点24 | 测点25 | 测点26 | 测点27 |
测点28 | 测点29 | 测点30 | 测点31 | 测点32 |
测点33 | 测点34 | 测点35 | 测点36 | 测点37 |
测点38 | 测点39 | 测点40 | 测点41 | 测点42 |
测点43 | 测点44 | 测点45 | 测点46 | 测点47 |
测点48 | 测点49 | 测点50 | 测点51 | 测点52 |
测点53 | 测点54 | 测点55 | 测点56 | 测点57 |
测点58 | 测点59 | 测点60 | 测点61 | 测点62 |
测点63 | 测点64 | Check Code | 01 | 03 |
80 | 00 79 | 00 7A | 00 7B | 00 7C |
00 7D | 00 7E | 00 7F | 00 80 | 00 81 |
00 82 | 00 83 | 00 84 | 00 85 | 00 86 |
00 87 | 00 88 | 00 89 | 00 8A | 00 8B |
00 8C | 00 8D | 00 8E | 00 8F | 00 90 |
00 91 | 00 92 | 00 93 | 00 94 | 00 95 |
00 96 | 00 97 | 00 98 | 00 99 | 00 9A |
00 9B | 00 9C | 00 9D | 00 9E | 00 9F |
00 A0 | 00 A1 | 00 A2 | 00 A3 | 00 A4 |
00 A5 | 00 A6 | 00 A7 | 00 A8 | 00 A9 |
00 AA | 00 AB | 00 AC | 00 AD | 00 AE |
00 AF | 00 B0 | 00 B1 | 00 B2 | 00 B3 |
00 B4 | 00 B5 | 00 B6 | 00 B7 | 00 B8 |
C7 FB |
2. Data Address Table
Address | Start Address | Description | Data type | Value range |
40258 | 01 01 | 1CH1# Temperature deposit | Read only | 0~65535 |
40259 | 01 02 | 1CH2# Temperature deposit | Read only | 0~65535 |
...... | ..... | (1Omit) | ... | ... |
40322 | 01 40 | 1CH64# Temperature deposit | Read only | 0~65535 |
40514 | 02 01 | 2CH1# Temperature deposit | Read only | 0~65535 |
40515 | 02 02 | 2CH2# Temperature deposit | Read only | 0~65535 |
...... | ..... | (2Omit) | ... | ... |
40578 | 02 40 | 2CH64 Temperature deposit | Read only | 0~65535 |
---- | ---- | Omit) | ---- | ---- |
40258 | 03 01 | 1CH1# Temperature deposit | Read only | 0~65535 |
40259 | 03 02 | 1CH2# Temperature deposit | Read only | 0~65535 |
...... | ..... | (1Omit) | ... | ... |
40322 | 03 40 | 1CH64# Temperature deposit | Read only | 0~65535 |
40101 | 00 64 | model code | read/write | |
0~65535 | 40102 | 00 65 | total points | read/write |
1~20 | 40103 | 00 66 | Device ID | read/write |
1~249 | 40104 | 00 67 | baud rate | read/write |
0~6 | 40105 | 00 68 | mode | read/write |
1~4 | 40106 | 00 69 | protocol | read/write |
1~10 | 40107 | 00 6A | interval | read/write |
0~36000 |
(1) Read or query device address
If you don't know the current device address and there is only one device on the bus, you can use the command FA 03 00 64 00 02 90 5F Query device address.
Device ID | Function id | Start Address | Data Length | CRC16 |
FA | 03 | 00 64 | 00 02 | 90 5F |
For the correct query command, the device will respond, for example the response data is: 01 03 02 07 12 3A 79, the format of which is as shown in the following table:
Device ID | Function id | Start Address | Model Code | CRC16 |
01 | 03 | 02 | 55 3C 00 01 | 3A 79 |
(2)Change device address
For example, if the current device address is 1, we want to change to 02, the command is:01 06 00 66 00 02 E8 14 .
Device ID | Function id | Start Address | Destination | CRC16 |
01 | 06 | 00 66 | 00 02 | E8 14 |
Device ID | Function id | Start Address | Destination | CRC16 |
01 | 06 | 00 66 | 00 02 | E8 27 |
4 Read and Modify Baud Rate
(1) Read baud rate
The device default factory baud rate is 9600. If you need to change it, you can change it according to the following table and the corresponding communication protocol. For example, read the current device's baud rate ID, the command is:01 03 00 67 00 01 35 D5 , its format is parsed as follows.
Device ID | Function id | Start Address | Data Length | CRC16 |
01 | 03 | 00 67 | 00 01 | 35 D5 |
For the correct query command, the device will respond, for example the response data is: 01 03 02 00 03 F8 45, the format of which is as shown in the following table:
Device ID | Function id | Data Length | Rate ID | CRC16 |
01 | 03 | 02 | 00 03 | F8 45 |
(2)Change the baud rate
For example, changing the baud rate from 9600 to 38400, ie changing the code from 3 to 5, the command is: 01 06 00 67 00 05 F8 1601 03 00 66 00 01 64 15 .
Device ID | Function id | Start Address | Target Baud Rate | CRC16 |
01 | 03 | 00 66 | 00 01 | 64 15 |
5 Read Correction Value
(1) Read Correction Value
When there is an error between the data and the reference standard, we can reduce the display error by adjusting the correction value. The correction difference can be modified to be plus or minus 1000, that is, the value range is 0-1000 or 64535 -65535. For example, when the display value is too small, we can correct it by adding 100. The command is: 01 03 00 6B 00 01 F5 D6 . In the command 100 is hex 0x64 If you need to reduce, you can set a negative value, such as -100, corresponding to the hexadecimal value of FF 9C, which is calculated as 100-65535=65435, and then converted to hexadecimal to 0x FF 9C. The correction value starts from 00 6B. We take the first parameter as an example. The correction value is read and modified in the same way for multiple parameters.
Device ID | Function id | Start Address | Data Length | CRC16 |
01 | 03 | 00 6B | 00 01 | F5 D6 |
Device ID | Function id | Data Length | Data value | CRC16 |
01 | 03 | 02 | 00 64 | B9 AF |
(2)Change correction value
For example, the current state quantity is too small, we want to add 1 to its true value, and the current value plus 100 correction operation command is:01 06 00 6B 00 64 F9 FD .
Device ID | Function id | Start Address | Destination | CRC16 |
01 | 06 | 00 6B | 00 64 | F9 FD |